SCOPE OF
EQUIPMENT
STANDARDS

TO BE USED
FOR  LOVAG

Standards for Low voltage Industrial Products

to be used for LOVAG Certification

Updated: November 2020

IEC EN or HD EQUIPMENT
  EN 50085 CABLE TRUNKING SYSTEMS AND CABLE DUCTING SYSTEMS FOR ELECTRICAL INSTALLATIONS
  EN 50085-1 Part 1: General requirements
IEC 60044   INSTRUMENT TRANSFORMERS
IEC 60044-7 EN 60044-7 Part 7: Electronic voltage transformers
IEC 60076   POWER TRANSFOMERS
IEC 60076-1 EN 60076-1 Power transformers - Part 1: General
IEC 60076-2 EN 60076-2 Part 2: Temperature rise for liquid-immersed transformers
IEC 60076-3 EN 60076-3 Part 3: Insulation levels, dielectric tests and external clearances in air
IEC 60076-5 EN 60076-5 Part 5: Ability to withstand short circuit
IEC 60076-6 EN 60076-6 Part 6: Reactors
IEC 60076-11 EN 60076-11 Part 11: Dry-type transformers
IEC 60076-13 EN 60076-13 Part 13: Self-protected liquid-filled transformers
IEC 60076-14 EN 60076-14 Part 14: Liquid-immersed power transformers using high-temperature insulation materials
IEC 60076-18 EN 60076-18 Part 18: Measurement of frequency response
IEC 61378-1 *) EN 61378-1 *) Converter transformers - Part 1: Transformers for industrial applications
EN 50464-1 *) Three-phase oil-immersed distribution transformers 50 Hz, from 50 kVA to 2 500 kVA with highest voltage for equipment not exceeding 36 kV – Part 1: General requirements
EN 50464-3 *) Three-phase oil-immersed distribution transformers 50 Hz, from 50 kVA to 2 500 kVA with highest voltage for equipment not exceeding 36 kV – Part 3: Determination of the power rating of a transformer loaded with non-sinusoidal currents
EN 50464-4 *) Three-phase oil-immersed distribution transformers 50 Hz, from 50 kVA to 2 500 kVA with highest voltage for equipment not exceeding 36 kV – Part 4: Requirements and tests concerning pressurised corrugated tanks.
EN 50541-1 *) Three phase dry-type distribution transformers 50 Hz, from 100 kVA to 3150 kVA, with highest voltage for equipment not exceeding 36 kV – Part 1: General requirements
EN 50588-1 *) Medium power transformers 50 Hz, with highest voltage for equipment not exceeding 36 kV - Part 1: General requirements
Remark: *) Although these standards exceed the low voltage area, they are included in the scope of LOVAG, because they may be applicable for products under the LOVAG agreement.
IEC 60252 AC MOTOR CAPACITORS
IEC 60252-1 EN 60252-1 Part 1: General - Performance, testing and rating - Safety requirements - Guidance for installation and operation
IEC 60252-2 EN 60252-2 Part 2: Motor start capacitors
IEC 60255 EN 60255 ELECTRICAL RELAYS
IEC 60255-12 - Part 12: Directional relays and power relays with two input energizing quantities
IEC 60255-13 - Part 13: Biased (percentage) differential relays
IEC 60269 EN 60269 LOW VOLTAGE FUSES
IEC 60269-1 EN 60269-1 Part 1: General requirements
IEC 60269-2 EN 60269-2 Part 2: Supplementary requirements for fuses for use by authorized persons
IEC 60269-3 EN 60269-3 Part 3: Supplementary requirements for fuses for use by unskilled persons for fuses for use by unskilled persons
IEC 60269-4 EN 60269-4 Part 4: Supplementary requirements for fuse-links for the protection of semiconductor devices
IEC 60309 EN60309 PLUGS, SOCKET-OUTLETS COUPLERS FOR INDUSTRIAL PURPOSES
IEC 60309-1 EN 60309-1 Part 1: General requirements
IEC 60309-2 EN 60309-2 Part 2: Dimensional interchangeability requirements for pin and contact-tube accessories
IEC 60439 IEC 61439 EN 61439 LOW VOLTAGE SWITCHGEAR AND CONTROLGEAR ASSEMBLIES
IEC 61439-6 EN 61439-6 Part 6: Busbar trunking systems (busways)
IEC 61439-7 EN 61439-7 Part 7: Assemblies for specific installations such as marinas, camping sites, market squares, electrical vehicles charging stations
IEC/TR 61641 Enclosed low-voltage switchgear and controlgear assemblies - Guide for testing under conditions of arcing due to internal fault
IEC 60831 SHUNT POWER CAPACITORS OF THE SELF-HEALING TYPE FOR A.C. SYSTEMS HAVING A RATED VOLTAGE UP TO AND INCLUDING 1 000 V
IEC 60831-1 EN 60831-1 Part 1: General - Performance, testing and rating - Safety requirements - Guide for installation and operation
IEC 60831-2 EN 60831-2 Part 2: Ageing test, self-healing test and destruction test
IEC 61869 INSTRUMENT TRANSFORMERS
IEC 61869-1 EN 61869-1 Part 1: General requirements
IEC 61869-2 EN 61869-2 Part 2: Additional requirements for current transformers
IEC 61869-3 EN 61869-3 Part 3: Additional requirements for inductive voltage transformers
IEC 61869-4 EN 61869-4 Part 4: Additional requirements for combined transformers
IEC 60931 SHUNT POWER CAPACITORS OF THE NON-SELF-HEALING TYPE FOR A.C. SYSTEMS HAVING A RATED VOLTAGE UP TO AND INCLUDING 1000 V
IEC 60931-1 EN 60931-1 Part 1: General - Performance, testing and rating - Safety requirements - Guide for installation and operation
IEC 60931-2 EN 60931-2 Part 2: Ageing test and destruction test
IEC 60931-3 EN 60931-3 Part 3: Internal fuses
IEC TR 60996 - Method for verifying accuracy of tan delta measurements applicable to capacitors
IEC 60947 EN 60947 LOW VOLTAGE SWITCHGEAR AND CONTROLGEAR
IEC 60947-1 EN 60947-1 Part 1: General rules
IEC 60947-2 EN 60947-2 Part 2: Circuit breakers
IEC 60947-3 EN 60947-3 Part 3: Switches, disconnectors, switch-disconnectors and fuse combination units
Part 4: Contactors and motor starters
IEC 60947-4-1 EN 60947-4-1 Sect. 1: Electrotechnical contactors and motor starters
IEC 60947-4-2 EN 60947-4-2 Sect. 2: AC semicontactor motor controllers and starters
IEC 60947-4-3 EN 60947-4-3 Sect. 3: AC semicontactor controllers and contactors for non-motor loads
Part 5: Control circuit devices and switching elements
IEC 60947-5-1 EN 60947-5-1 Sect. 1: Electromechanical control circuit devices
IEC 60947-5-2 EN 60947-5-2 Sect. 2: Proximity switches
IEC 60947-5-5 EN 60947-5-5 Sect. 5: Electrical emergency stop devices with mechanical latching function
IEC 60947-5-6 EN 60947-5-6 Sect. 6: DC interface for proximity sensors and switching amplifiers (NAMUR)
IEC 60947-5-8 EN 60947-5-8 Sect. 8: Enabling control devices
IEC 60947-5-9 EN 60947-5-9 Sect. 9: Flow rate switches
Part 6: Multiple function equipment
IEC 60947-6-1 EN 60947-6-1 Sect. 1: Automatic transfer switching equipment
IEC 60947-6-2 EN 60947-6-2 Sect. 2: Control and protective switching devices (CPS)
Part 7: Ancillary Equipment
IEC 60947-7-1 EN 60947-7-1 Sect. 1: Terminal blocks for copper conductors
IEC 60947-7-2 EN 60947-7-2 Sect. 2: Protective conductor terminal blocks for copper conductors
IEC 60947-7-3 EN 60947-7-3 Sect. 3: Ancillary equipment - Safety requirements for fuse terminal blocks
IEC 60947-7-4 EN 60947-7-4 Sect. 4: Ancillary equipment – PCB terminal blocks for copper conductors
IEC 60947-8 EN 60947-8 Part 8: Control units for built-in thermal protection (PTC) for rotating electrical machines
IEC 61131 EN 61131 PROGRAMMABLE CONTROLLERS
IEC 61131-1 EN 61131-1 Part 1: General information
IEC 61131-2 EN 61131-2 Part 2: Equipment requirements
IEC 61386 EN 61386 CONDUIT SYSTEMS FOR CABLE MANAGEMENT
IEC 61386-1 EN 61386-1 Part 1: General requirements
IEC 61386-21 EN 61386-21 Part 21: Particular requirements - Rigid conduit systems
IEC 61386-22 EN 61386-22 Part 22: Particular requirements - Pliable conduit systems
IEC 61386-23 EN 61386-23 Part 23: Particular requirements - Flexible conduit systems
IEC 61386-24 EN 61386-24 Part 24: Particular requirement - Conduit systems buried underground
IEC 61558 EN 61558 SAFETY OF TRANSFORMERS POWER SUPPLY UNITS AND SIMILAR
IEC 61558-1 EN 61558-1 Part 1: General requirements and tests
IEC 61558-2-1 EN 61558-2-1 Part 2-1: Particular requirements for separating transformers for general use
IEC 61558-2-2 EN 61558-2-2 Part 2-2: Particular requirements and tests for control transformers and power supplies incorporating control transformers
IEC 61558-2-3 EN 61558-2-3 Part 2-3: Particular requirements and tests for ignition transformers for gas and oil burners
IEC 61558-2-4 EN 61558-2-4 Part 2-4: Particular requirements for isolating transformers for general use
IEC 61558-2-5 EN 61558-2-5 Part 2-5: Particular requirements and test for transformer for shavers, power supply units for shavers and shaver supply units
IEC 61558-2-6 EN 61558-2-6 Part 2-6: Particular requirements and tests for safety isolating transformers and power supply units incorporating safety isolating transformers
IEC 61558-2-7 EN 61558-2-7 *) Part 2-7: Particular requirements and tests for transformers and power supplies for toys *) EN modified
IEC 61558-2-8 EN 61558-2-8 Part 2-8: Particular requirements and tests for transformers and power supply units for bells and chimes
IEC 61558-2-9 EN 61558-2-9 Part 2-9: Particular requirements and tests for transformers and power supply units for class III handlamps for tungsten filament lamps
IEC 61558-2-10 EN 61558-2-10 Part 2-10: Particular requirements and tests for separating transformers with high insulation level and separating transformers with output voltages exceeding 1 000 V
IEC 61558-2-12 EN 61558-2-12 Part 2-12: Particular requirements and tests for constant voltage transformers and power supply units for constant voltage
IEC 61558-2-13 EN 61558-2-13 Part 2-13: Particular requirements and tests for auto transformers and power supply units incorporating auto transformers
IEC 61558-2-14 EN 61558-2-14 Part 2-14: Particular requirements and tests for variable transformers and power supply units incorporating variable transformers
IEC 61558-2-15 EN 61558-2-15 Part 2-15: Particular requirements and tests for isolating transformers for the supply of medical locations
IEC 61558-2-16 EN 61558-2-16 Part 2-16: Particular requirements and tests for switch mode power supply units and transformers for switch mode power supply units
IEC 61558-2-20 EN 61558-2-20 Part 2-20: Particular requirements and tests for small reactors
IEC 61558-2-23 EN 61558-2-23 Part 2-23: Particular requirements and tests for transformers and power supply units for construction sites
IEC 61558-2-26 EN 61558-2-26 Part 2-26: particular requirements and tests for transformers and power supply units all for saving energy and other purposes
IEC 61642 INDUSTRIAL A.C. NETWORKS AFFECTED BY HARMONICS - APPLICATION OF FILTERS AND SHUNT CAPACITORS
IEC 61643 LOW-VOLTAGE SURGE PROTECTIVE DEVICES
IEC 61643-11 EN 61643-11 **) Part 11: Surge protective devices connected to low-voltage power systems - Requirements and test methods *) EN modified
IEC 61643-12 - Part 12: Surge protective devices connected to low-voltage power distribution systems - Selection and application principles
IEC 61643-21 EN 61643-21 **) Part 21: Surge protective devices connected to telecommunications and signaling networks - Performance requirements and testing methods **) EN modified
IEC 61812 EN 61812 SPECIFIED TIME RELAYS FOR INDUSTRIAL USE
IEC 61812-1 EN 61812-1 Part 1: Requirements and tests
IEC 61851 EN 61851 ELECTRIC VEHICLE CONDUCTIVE CHARGING SYSTEM
IEC 61851-1 EN 61851-1 Part 1: General requirements
IEC 61851-23 EN 61851-23 Part 23: DC electric vehicle charging station
IEC 62196-1 EN 62196-1 Part 1: General requirements
IEC 62196-2 EN 62196-2 Part 2: Dimensional compatibility and interchangeability requirements for a.c. pin and contact-tube accessories
IEC 61921 POWER CAPACITORS - LOW-VOLTAGE POWER FACTOR CORRECTION BANKS
IEC 62208 EN 62208 EMPTY ENCLOSURES FOR LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR ASSEMBLIES
IEC 62208 EN 62208 General requirements
IEC 60240 UNINTERRUPTIBLE POWER SYSTEMS (UPS)
IEC 62040-1 EN 62040-1 Part 1: General and safety requirements for UPS
IEC 62040-2 - Part 2: Electromagnetic compatibility (EMC) requirements
IEC 62041 SAFETY OF TRANSFORMERS, REACTORS, POWER SUPPLY UNITS AND COMBINATIONS THEREOF - EMC REQUIREMENTS

Horizontal standards to be used for LOVAG

Number of Standard
IEC EN or HD EQUIPMENT
IEC 60068 EN 60068 ENVIRONMENTAL TESTING - Part 2: Tests
IEC 60068-2-6 EN 60068-2-6 Test Fc: Vibration (sinusoidal)
IEC 60068-2-11 EN 60068-2-11 Test Ka Salt mist
IEC 60068-2-20 Test T: Soldering
IEC 60068-2-27 EN 60068-2-27 Test Ea and guidance: Shock
IEC 60068-2-30 EN 60068-2-30 Test Db and guidance: Damp heat, cyclic (12 + 12 hour cycle)
IEC 60529 EN 60529 DEGREES OF PROTECTION PROVIDED BY ENCLOSURES
IEC 60529 EN 60529 Degrees of protection provided by enclosures (IP Code)
IEC 61000 EN 61000 ELECTROMAGNETIC COMPATIBILITY (EMC)
Part 3: Limits
IEC 61000-3-2 EN 61000-3-2 Part 3-2: Limits for harmonic current emission (equipment input current <= 16 A per phase)
IEC 61000-3-3 EN 61000-3-3 Part 3-3: Limitation of voltage changes, voltage fluctuations flicker in public low voltage supply systems, for equipment with rated current <= 16 A per phase and not subjected to conditional connection
Part 4: Testing and measurement techniques
IEC 61000-4-2 EN 61000-4-2 Part 4-2: Electrostatic discharge immunity test
IEC 61000-4-3 EN 61000-4-3 Part 4-3: Radiated radio frequency, electromagnetic field immunity
IEC 61000-4-4 EN 61000-4-4 Part 4-4: Electrical fast transient/burst
IEC 61000-4-5 EN 61000-4-5 Part 4-5: Surge immunity test
IEC 61000-4-6 EN 61000-4-6 Part 4-6: Immunity to conducted disturbances, induced by radio-frequency fields
IEC 61000-4-8 EN 61000-4-8 Part 4-8: Power frequency magnetic field immunity test
IEC 61000-4-9 EN 61000-4-9 Part 4-9: Pulse magnetic field immunity test
IEC 61000-4-10 EN 61000-4-10 Part 4-10: Damped oscillator magnetic field immunity test
IEC 61000-4-11 EN 61000-4-11 Part 4-11: Voltage dips, short interruptions and voltage variation immunity tests
Part 6: Generic standards
IEC 61000-6-3 EN 61000-6-3 Part 6-3: Generic standards -Emission standard for residential commercial and light industrial environments
IEC 61000-6-4 EN 61000-6-4 Part 6-4: Generic standards -Emission standard for industrial environments

 

Remarks:
Beige-shadowed Standards: These standards are only used for LOVAG Test Reports and LOVAG Certificates